 |
These brackets allow
for bolt-in tubes in a roll cage, see below for a typical application.. They are £9 a
set plus VAT and
shipping. A set consists of a pointy plate (that is one shown on the left side
or one on the right side) plus a flat
plate (shown in the middle) plus two suitable nuts and bolts to join the two.
|
 |
Roll cage brackets used in a VW Jetta for
removable door bars. Pointy plate on main loop and flat plate on the bar. |
 |
These are our standard DZUS style brackets, available from
stock. They all cost £1.20. |
 |
These are standard chrome moly threaded
inserts to be welded
into tubes.
From left to right: 3/8th
UNF thread for 5/8th 0.058 wall tube (left and right thread available);
3/8th UNF thread for 3/4 0.058 tube (left and right thread available);
7/16th UNF for 3/4 0.058 tube (left and right thread available); 3/4 UNF for
1 1/4 0.120 tube (left hand thread available).
We also stock
Aurora rod ends in
suitable sizes to fit. |
 |
From left to right: 7/16th UNF thread for 7/8
tube; 1/2 UNF thread for 1 inch 0.058 wall tube (left and right thread
available); 5/8th UNF thread for 1 inch 0.058 tube (left and right thread
available); 3/4 UNF thread for 1 1/4 inch 0.095 tube (right thread
available). We have inserts
suitable for 1 1/4 inch 0.095 and 0.120 wall tube and 1 3/8 inch 0.095 or 0.120 wall
tube in left hand thread with a hex as above and right hand thread plain as
on the left. These are normally paired on for example a four-link tube. |
 |
This is our standard driveshaft loop with pip
pins for easy removal. Also shown is our bracket for track locator or
A-frame locators. Loop kit with
"quick pins" is £26, price for "pip pins" on application. The track locator
bracket is £35. |
 |
1 - wheelie bar ends (when folded) £2
2 - ladder bar plate for axle £14 each
3 - master cylinder mount £3.50
4 - suspension inners (in pairs) £4.00
In the middle small tabs for brake
lines/fittings and windows, all £1.20 |
 |
1 - Brake caliper bracket £5
2 - Strut top, will be folded for use £4.50
3 - Motor plate mount £2.50
4 - Bracket 4 above before folding and
drilling £1.50
plus other miscellaneous brackets, all £1.50 |
 |
The “weld-in” clevises
shown here are 1/2 inch tube id x 1/4 inch pin, 5/8 inch tube id x 5/16
pin and 7/8 inch tube id by 3/8 inch pin sizes.
We have sizes from 1/2
inch x 1/4 inch to 1 3/4 inch x 5/8 inch.
Prices from £6.50 to £9.00
|
 |
These washer/spacers are
available in 3/8th , 7/16th and 1/2 inch sizes. They
are available in stainless steel.
Any size £2.50
|
|
 |
These flanges are designed to be used on turbo-charger
manifolds to allow them to be build up in sections. They are intended to be used
in pairs although the 3 inch/6 hole flange will fit some turbochargers. We can
fabricate complete systems for you based on these components.
The flange shown here is intended for 2.5 inch tubes and provided with two
bolt holes. |
|
 |
Intended for 3.0 inch tubes and provided with two
bolt holes |
|
 |
Intended for 3.0 inch tubes and provided with
three bolt holes |
|
 |
Intended for 3.0 inch tubes and provided with six
bolt holes |
|
 |
Parachute release kit comprising
- Cable
- Lever
- Chassis bracket
- Mounting and connecting hardware
|
|
 |
Lever end as installed in an ARRC customer car.
The lever has been anodised in this installation.
Click here
to go back to the top of the page. |
|
 |
Door latch and lock kit comprising
-
catches
-
strikers
-
door cover plates
-
mounting bolts
-
extension tabs for the lock levers
|
|
 |
Lock kit as installed in door, view from
outside and down from above through window glass opening.
No internal door handle mechanism fitted yet and
installation not finalised in these pictures. |
|
 |
Striker fitted through bodywork onto small
bracket welded to main loop of tubular frame chassis.
Click here
to go back to the top of the page. |
|
 |
Electric window regulators as fitted to luxury
super cars. Kit comes with
- pair of regulators, as seen
- switches, not shown
- wiring, not shown
|
|
 |
Seen here in correct orientation for door.
Window glass fits in silver coloured horizontal fitting which moves up and
down the plated guide. Adaptable
to most situations, please contact us if you wish to check dimensions.
Maximum lift, depending on installation, is 23 inches
The picture is pixellated to preserve the
anonymity of the model. Click
here to go back to the top
of the page. |
|
 |
Machined billet
6082-T6 aluminium Nitrous bottle mounts, suitable for 10 or 15 pound bottles. Shown
mounted on stainless display rails which are not included in the kit.
Mounts are at two different heights to hold
bottle at a suitable angle when mounted on a flat floor.
Clamps undo completely to allow easy
installation and removal of the bottle. |
|
 |
Shown here with sample bottle (not included in
the kit) installed. |
|
 |
This shows the rubber inserts which hold the
bottle firmly and allow for minor variations in size.
Click here
to go back to the top of the page. |
|
 |
This is our standard battery box. It is
laser cut from sheet steel, then folded and welded in our workshop. It is
supplied with the clamping bracket shown which can be positioned to suit many
different sizes of battery. Maximum dimensions for this box 27x19x22 cm
(WxDxH) |
|
 |
This shows a typical installation in one of our
chassis.
Click here
to go back to the top of the page. |
